国际完美世界下载,小说阅读网,唐家三少

產品分類 CATEGORY

聯系方式 Contact

東莞市高圣部品精密電子科技有限公司
電話：86-769-8200 6969
傳真：86-769-8200 6196
E-Mail： [email protected]
網址：www.gaofengdz.com
聯系人：吳先生/135 8082 6835
地址：東莞市塘廈鎮清湖頭社區清湖路1號必富工業園

您的位置: 首頁 -> 產品中心 -> 開關系列 -> 撥動開關系列 -> 正撥SS -> 撥動開關SS-12D06

[查看原圖片] [返回]

[上一個:撥動開關SS-12D03] [下一個:撥動開關SS-12D08]

撥動開關SS-12D06

詳情說明

主要技術參數/ Main data
1、RATING（額定值）：1.5A 125V AC
2、FUNCTION（接觸型式）：1P2T
3、TIMING（時間特性）：NO SHORTING
4、ELECTRICAL CHARACTERISTICS（電氣性能規格）：
ITEM 項目		TEST CONDITIONS 測試條件	PERFORMANCE 規格
4.1	CONTACT RESISTANCE 接觸電阻	MEASURED AT SMALL CURRENT(100mA OR LESS) 在微小電流(100mA)以下，撥動三次后測試.	100mΩMAX. 100毫歐以下.
4.2	INSULATION RESISTANCE 絕緣電阻	APPLY A VOLTAGE OF 500V DC FOR 1 MIN. TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE. {C}(1)BETWEEN BODY AND TERMINAL {C}(2)BETWEEN TERMINALS 輸入500V DC 電壓1分鐘,按以下接觸方法測試: {C}(1)外殼與排腳之間。 {C}(2)端子之間。	100MΩMIN. 100兆歐以上.
4.3	DIELECTRIC STRENGTH 耐電壓	AC500V(50-60Hz)FOR 1 MIN TRIP CURRENT:0.5mA BETWEEN TERMINALS. BETWEEN INDIVIDUAL TERMINALS AND FRAME. 輸入500V(50-60Hz)電壓,1分鐘感度電流為0.5mA,按以下接觸方法測試: (1)排腳相互之間 (2)排腳與外殼之間	WITHOUT DAMAGETOPARTS ARCING OR BREAKDOWN ETC 沒有絕緣破壞等異常
5、MECHANICAL CHARACTERISTICS (機械性能規格)
ITEM 項目		TEST CONDITIONS 測試條件	PERFORMANCE 規格
5.1	OPERATING FORCE 作動力	MEASUREMENT SHALL BE MADE ST THE NEAREST POINTF OF THE COMPONENT OR AT THE POINT 3mm FROM THE TIP OF THE ACTUATOU(KNOB0) 在距離膠柄3mm作測定點，撥動三次后測試。	300gf±100gf
5.2	TERMINAL STRENGTH 端子強度	A STATIC LOAD OF(500gf)SHALL BE APPLIED TO THE TERMINAL FOR 15 SEC,IN ANY DIRECTON. 在排腳前端任意一個方向加(500gf)力度測試,時間為15秒.	MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED WITHOUT LOOSENESS OF ACTUATOU. 在端子中沒有裂開,松動等異常,滿足于機械、電器性能。
5.3	DISPLACEMENT OF ACTUATOR (KNOB) 柄強度	A STATIC LOAD OF 10N(1Kgf)SHALL BE APPLIED TO THE TOP OF THE ACTUATOR(KNOB)AND THEN DESPLACEMENT SHALL BE MEASURED TO THE DIRECTION OF THE ARROW. 在柄的前端施加1Kgf的力度,位移應沿印記的方向上定.	THE LEVER SHALL HAVE NO SERIOUS DEFORMATION AND FUNCTION IS NORMALLY. 柄部無嚴重變形,可以正常工作
6、ENDURANCE CHARACTERISTICS (耐久性) :
ITEM 項目		TEST CONDITIONS 測試條件	PERFORMANCE 規格
6.1	LIFE TEST 壽命試驗	ENDURANCE WITHOUT LOADING： A SWITCH SHALL BE SUBJECTED TO 10,000 CYCLES AT A SPEED OF 15 TO 18 CYCLES PER MINUTE WITHORT LOADING. 無負荷: 在無負荷的條件下以每分鐘15—18回的速度進行10,000次的測試.	(1)CONTACT RESISTANCE(接觸電阻) 200mΩ MAX.200毫歐以下. (2)INSULATION RESISTANCE(絕緣電阻) 50MΩ MIN. 50兆歐以上. (3)WITHSTAND VOLTAGE(耐電壓) AC 500V,1 MINUTE.AC 500V 1分鐘 (4)OPERATING FORCE(作動力) ±30%INITIAL VALUE. 變化范圍初始值±30% (5)WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. (測試后外表無損傷,并且滿足機械性能)
6.2	SOLDERA-BILITY TEST 可焊性試驗	THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 230±5℃ FOR 3±0.5 SECONDS. 端子頂部被浸入錫焊池中2mm深,溫度為 230±5℃,時間為3±0.5秒.	(1) SOLDER WELTING TIME SHALLBE 3 SEC OR LESS. 焊接時間少于3秒 (2) THE AREA OF SOLDERING SHOULD BE OVER 75% 焊接面積要有75%以上.
6.3	RESISTANCE TO SOLDERING HEAT TEST 耐焊性試驗	SOLDER BATH METHOD: SOLDER TEMPERATURE 260±5℃ IMMERSION TIME3±0.5 SEC IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD 1.6mm DIMENSIONS OF COMPONENT HOLES IN THE PRINTED WIRING BOARD SHALL BEING ACCORDANCE WITH THOSE SPECIFIED IN THES SPECIFICATION. 焊爐焊接的時候溫度控制在260±5℃,過爐時間為3±0.5秒,于基板厚度為1.6mm SOLDERING IRON METHOD: BIT TEMPERATURE 350±10℃ APPLICATION TIME OF SOLDERING IRON3±0.5SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL. 手焊接的時候溫度控制在350±10℃,時間為3±0.5秒,但不能在排腳上施加異常壓力	WITHORT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTCS SHALL BE SATISFIED. 本體無變形,能滿足于機械、電氣性能。
6.4	COLD TEST 耐冷試驗	THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -25±3℃ FOR48HOURS. THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置在溫度-25±3℃中48小時后,再放置常溫中1小時來進行測試.	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. 外觀無異常,滿足于機械、電氣性能
6.5	HEAT TEST 耐熱試驗	THE SWITCH SHALL BE STORED ATA TEMPERATURE OF70±2℃ FOR 48 HOURS. THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置在溫度70±2℃中測試48小時后,再放置正常室溫中1小時來測定.	THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. 外觀無異常,滿足于機械、電器性能.
6.6	HUMIDITY TEST 潮濕試驗	THE SWITCH SHALL BE STORED ATA TEMPERATURE OF 40±2℃ AND A HUMIFITY OF 90% TO 95% FOR 96 HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置40±2℃的相對濕度為90%～95%環境中96小時后,再將樣板放在正常環境1小時后進行測試.
6.7	STANDARD ATMOSPHERE CONDITIONS 測試標準狀態	UNLESS OTHERWISE SPECIFIED. THE STANDARD RANGE OF ATMOSPHERE CONDITIONS FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS: (1)AMBIENT TEMPERATURE:5℃ TO 35℃ (2)RELATIVE HUMIDITY:45% TO 85% (3)AIT PRESSURE :86Kpa TO 106Kpa 在沒有指定的情況下測試溫度、濕度、氣壓如下: (1)溫度為5℃—35℃. (2)濕度為45%—85%. (3)氣壓為86Kpa—106Kpa.
6.8	PRACTICAL TEMPERATURE RANCE 使用溫度范圍	AT-16℃—+60℃. 在-16℃—+60℃內使用.